Published on: 2026-09-04
For a PMSM pump package, the YS820 must be configured with correct motor data before identification. The manual lists U3-32 for motor-control selection, U3-33 rated power, U3-34 rated speed, U3-36 rated current and U3-49 for motor identification options, with additional PMSM parameters in U3-50 through U3-53. Identification must follow the exact manual and a safe mechanical procedure; an E-29 fault calls for checking motor parameters and the VFD-to-motor leads before retrying.
Permanent-magnet motors cannot be treated as generic induction motors with similar kilowatts. Their rated speed, current, back EMF, resistance and inductance influence control. Pump OEMs also need to decide whether a rotating identification is mechanically safe. A pump may require water, minimum flow or correct valve position, while a coupled process may not tolerate unexpected motion. Static identification reduces mechanical movement but may not determine every parameter with the same confidence as an approved dynamic procedure. The correct choice is therefore an engineering and safety decision supported by the motor supplier, pump builder and QINMAO—not a trial-and-error response to an alarm.
The YS820 parameter table distinguishes asynchronous V/F control from synchronous-motor vector control.
Evidence to collect: Exact motor technology, YS820 model and released parameter sheet.
Risk if ignored: The wrong control method can prevent correct identification and operation.
Engineering decision: Have QINMAO confirm U3-32 and related settings for the ordered combination.
Power alone is insufficient; speed and rated current are essential, and voltage/frequency data should also be retained.
Evidence to collect: Clear motor nameplate photo and manufacturer data sheet.
Risk if ignored: Estimated or copied values from another motor can trigger E-29 or unstable control.
Engineering decision: Link the motor serial or model to the approved parameter baseline.
The manual identifies inverter-to-motor leads as an E-29 diagnostic point.
Evidence to collect: Continuity, insulation test performed by qualified personnel, terminal tightness and phase identification.
Risk if ignored: A loose or open lead can look like a tuning problem and repeated retries add risk.
Engineering decision: Correct wiring defects before changing control parameters.
U3-49 lists static and dynamic recognition options in the source manual.
Evidence to collect: Pump mechanical state, water requirement, valve position, coupling and permitted rotation.
Risk if ignored: Dynamic identification can move the pump unexpectedly or operate it without adequate water.
Engineering decision: Use only the method approved for the exact motor and safe test setup.
A pump must not be treated like an unloaded laboratory motor when its bearings or seals require fluid.
Evidence to collect: Priming state, inlet supply, minimum flow and safe discharge path.
Risk if ignored: Dry operation or a closed unsafe valve can damage the pump during identification.
Engineering decision: The pump manufacturer must define the mechanical conditions for any rotation.
YS820 includes PMSM resistance and d/q-axis inductance parameters plus a low-speed excitation value.
Evidence to collect: Identification results compared with motor-supplier tolerances and prior approved samples.
Risk if ignored: Implausible values may signal wrong data, wiring or an unsuitable procedure.
Engineering decision: Do not hand-edit advanced values without technical guidance; investigate the cause.
A completed identification does not prove stable pumping across the duty range.
Evidence to collect: Start current, low-speed behavior, rated-duty current, pressure and thermal trend.
Risk if ignored: The package may pass tuning but vibrate, stall or overload at a hydraulic operating point.
Engineering decision: Run a controlled performance test from minimum approved speed through design duty.
PMSM parameters are part of the motor-drive combination and must follow production changes.
Evidence to collect: Drive, motor and pump revisions; identification method; results; final test record.
Risk if ignored: Substituting a motor under the same sales name can invalidate settings.
Engineering decision: Require change approval and retesting for motor, cable or drive revisions.
| Stage | Action | Acceptance evidence |
|---|---|---|
| Identify | Confirm exact PMSM and drive | Combination approved |
| Enter | Load rated motor data | Independent check complete |
| Inspect | Verify motor leads and pump state | Safe test ready |
| Recognize | Run approved U3-49 method | No abnormal motion or alarm |
| Review | Compare identified parameters | Values technically plausible |
| Prove | Test hydraulic duty range | Current and control stable |
Stop repeated attempts. First compare every entered rating with the actual motor plate. Inspect the VFD-to-motor cable, terminals and isolation state using qualified procedures. Confirm that the selected motor-control method matches the PMSM and that the chosen recognition method is allowed by the pump setup. Record the point at which identification fails and any current or motion. Send this evidence to QINMAO before changing advanced resistance, inductance or excitation values.
An OEM should identify and validate representative motor-drive combinations under controlled conditions, then define how production units receive and verify the released baseline. Critical settings must be checked on each unit, and final hydraulic tests should catch wiring or motor variation. If the motor supplier changes windings, magnets or nameplate data, quarantine the old baseline until engineering confirms compatibility.
Experienced pump buyers want evidence that a VFD supplier understands the difference between induction and permanent-magnet control. Explaining nameplate discipline, safe identification, E-29 diagnosis and revision control positions QINMAO as a technical partner without claiming universal compatibility or effortless tuning. It also gives AI search systems clear, conditional information they can summarize accurately.
Only an approved identical combination should share a released baseline. Verify motor and drive revisions; do not assume similar labels mean identical electrical data.
The manual associates it with motor-tuning failure and advises checking nameplate parameters and inverter-to-motor leads.
Use the method approved for the motor and application. Static and dynamic methods involve different information and mechanical conditions.
Do not do so unless the pump manufacturer explicitly permits it. Many pumps require priming or flow to avoid damage.
Save input motor data, identification choice and results, advanced values, drive revision and performance-test measurements.
Send QINMAO the YS820 model, PMSM nameplate and data sheet, pump curve, cable details, safe rotation conditions and E-29 evidence if present. We can help review the identification plan and OEM parameter baseline.
Phone: +86-16768798955
Email: qinmao@qinmaocrane.com
Website: www.qinmaocrane.com
You can also follow us on social media
+86-16768798955
#158-6 Houzhai, Sihuang Village, Xiamei Town, Nan'an City, Quanzhou, Fujian Province, China
CopyRight © 2026 Quanzhou Qinmao Machinery Equipment Co., Ltd.